You need about a dozen tools to start woodworking, bought in four stages: measuring and marking tools, something to cut with, a drill and clamps for assembly, and a sander. A workable kit costs $200 to $500 in the US as of November 2026. Big machines come later, when a project demands them.
This is a buying guide, not a product roundup. Prices below are approximate US street prices checked in November 2026; they vary by retailer, region, and sale timing, so treat them as ranges rather than quotes. The order matters more than the picks: each stage below adds a kind of work you could not do before, and buying out of order is how beginners end up with a $700 saw and no square.
The criteria that actually matter
Four things decide whether a beginner tool earns its place.
Does a project need it now? Every tool below is justified by the stage of work it enables, not by what a workshop tour video contains.
Does it do accurate work cheaply? A $10 speed square and a $130 combination square both mark a line across a board. The expensive one is nicer; the cheap one is not wrong.
Does it have a consumable cost? Saws need blades, sanders need discs, drills need bits, and batteries drive cordless prices. The sticker is never the whole cost.
Can one tool do the job of two? A circular saw with a straightedge rips and crosscuts. A drill/driver drills and drives. Single-purpose tools wait until their job is a real bottleneck.
Stage 1: Measure and mark, about $40 to $90
Buy these first, on day one, because every later tool depends on them.
- Tape measure, 16 to 25 feet: $10 to $20. A 25-foot tape is standard; what matters is a standout you can read and a lock that holds.
- Speed square, 7 inch: about $10. Marks square lines, guides a circular saw, checks corners. Possibly the best $10 in woodworking.
- Combination square, 12 inch: $15 to $60. Sets and checks depths and 90- and 45-degree layout. The cheap end works; the Starrett end lasts a lifetime.
- Marking knife or sharp pencil: $5 to $15. A knife line is more precise than a pencil line and gives a chisel somewhere to register.
- A quality straightedge or level, if sheet goods are in the plan: $20 to $40.
Stage 2: Something to cut with, $40 to $180
Two honest paths here.
The hand path: a Japanese pull saw in the $30 to $50 range crosscuts and rips cleanly, teaches saw control, and is quiet enough for an apartment. Add a coping saw later for curves. Total: about $40 to $70.
The power path: a corded circular saw, $60 to $140, paired with the speed square or a straightedge as a guide, breaks down sheet goods and crosscuts dimensional lumber accurately. Cordless versions run $85 to $185 as a bare tool, plus battery and charger if you are not already on a platform. For most first projects, a circular saw plus a straightedge replaces a table saw entirely.
A jigsaw, $60 to $140, is the next cutting tool when a project needs curves or interior cutouts, but it is not a day-one purchase.
Stage 3: Assemble, $150 to $320
Assembly is a drill, clamps, and glue.
- Cordless drill/driver with battery and charger: $100 to $200. Drills pilot holes, countersinks, and drives screws. Pick a battery platform you can live with, because future cordless tools will share it.
- Drill and driver bit set: $20 to $40. Brad-point bits for wood, a countersink, and driver bits cover a first year of projects.
- Four to six clamps: $40 to $80 mixed. Two 24-inch bar or F-style clamps, a couple of spring clamps, and a 6-inch pair handle small glue-ups. The screw size reference tells you which fastener and pilot hole a joint actually wants.
- Wood glue: about $8 for a bottle of PVA that will outlast several projects.
Stage 4: Finish, $60 to $140
- Random orbit sander, corded 5 inch: $50 to $110. The Bosch ROS20VSC class of sander sits around $70 and is the standard first pick; corded beats cordless here because sanding is the longest continuous runtime in any project.
- Sandpaper assortment, 80 through 220 grit: $15 to $25.
- Safety gear: $30 to $50 for eye protection, hearing protection, and a dust mask or respirator. Non-negotiable at any budget.
Block planes, chisels, and sharpening gear are worth adding in this stage if your projects lean toward hand fitting: a four-piece Narex-class chisel set runs $30 to $90 and a sharpening stone another $30 to $90. They are optional for a screwed-and-glued first project and essential by the time you are cutting joints.
Stage 5: The machines that wait
These are the tools beginners buy too early. None is wrong to own; all are wrong to own before a project requires them.
- Table saw, jobsite class: $280 to $650. A jobsite saw like the Skil TS6307-00 class sits around $280 to $330, and contractor hybrids run higher. Buy it when repeatable ripping is the actual bottleneck, and not before. Until then the circular saw and straightedge do the work.
- Miter saw, 10 inch: $110 to $280. Repeatable crosscuts and trim. Worth it early only if your projects are mostly crosscutting dimensional lumber.
- Router, mid-size fixed or combo base: $120 to $250. A 2-1/4 HP combo kit in the Bosch 1617 class covers edges, dados, and joinery. Bits are extra, $15 to $40 each, bought one at a time as joints demand.
- Shop vacuum or dust extractor: $100 to $220. This one arguably belongs earlier than the machines; sawdust control is part of running the other tools, and a vac with tool-activated switching makes every sander and saw session cleaner.
What to skip
- The 100-piece master tool kit. Two-thirds of it is filler; buy the dozen tools above instead.
- Track saws, planers, jointers, and band saws in year one. Each solves a problem you have not hit yet.
- Cordless versions of long-runtime tools like sanders, where the battery dies mid-job.
- Premium brands at the measuring stage. Spend on the tools that touch wood: saw, chisels, plane iron.
Total cost of ownership
Budget beyond the sticker. A circular saw wants a decent thin-kerf blade ($20 to $40). A router wants bits. A table saw wants a better blade than it ships with plus push sticks. Cordless tools want a second battery eventually. Consumables (sandpaper, glue, screws, finish) run $20 to $50 per small project. A sensible year-one budget is the kit price plus about 20 percent for blades, bits, and the stuff that gets used up.
Frequently asked questions
What is the single most important first tool?
A tape measure and a square, because every later tool depends on accurate layout. Of the power tools, a drill/driver touches more first projects than anything else.
Should I buy corded or cordless tools?
Cordless for the drill, where mobility matters and runtime is short. Corded for the sander and circular saw, where runtime is long and the price is lower. The exception: if you already own batteries on a platform, staying on it saves real money.
Is a table saw worth it for a beginner?
Not as a first purchase. A circular saw with a straightedge does the same cuts more safely for less money, and the table saw earns its cost only when you are ripping parts repeatedly. When that day comes, the jobsite class at $280 to $650 covers most small-shop work.
What tools do I need for a specific first project like a shelf?
A tape measure, speed square, saw (handsaw or circular saw), drill, two clamps, sandpaper, glue and screws. That is the whole kit for most first projects.
Next steps
- New to the craft entirely: how to start woodworking as a beginner
- Price the lumber for a first project: board foot calculator and lumber cost estimator
- Pick forgiving, cheap stock: eastern white pine
- See the joints these tools will cut: types of wood joints