A dado is a flat-bottomed channel cut across the grain of a board, sized so a mating part slides into it and locks on three sides. Cut one with a stacked dado set or repeated passes on a table saw, or with a straight bit in a router guided by an edge or jig.
The dado is the standard joint for shelves and cabinet interiors because it carries weight on wood rather than on a glue line and it holds the carcass square during assembly. It is one member of the groove family described in the types of wood joints guide; this page covers the terminology, the two cutting methods, and where the joint belongs.
Dado, groove, rabbet: the differences
The three joints are the same channel moved around. A dado is cut across the grain, into the face of a board. A groove is the same channel cut with the grain, usually along an edge to hold a panel or drawer bottom. A rabbet is the channel moved all the way to the edge, so it is open on two sides.
The practical consequence: dados and rabbets go where a part needs to be supported or registered (shelves, backs, dividers), and grooves go where a panel needs to be retained while still moving (frame-and-panel doors, drawer bottoms). The dado glossary entry covers the terminology, including the regional spelling "dado" versus "housing" in British usage.
Where dados belong
- Bookshelves and bookcases: the shelf end sits in the dado, which resists sag and keeps the sides from racking.
- Cabinet carcasses: fixed shelves, dividers, and bottoms all register in dados so the box assembles square.
- Drawer construction: a dado or groove near the bottom of the sides holds the drawer bottom.
- Wall cleats and partitions: anywhere a board must intersect another at 90 degrees and carry load.
Depth guideline: about one-third of the stock thickness for standard work in 3/4 inch material, and never more than half. Deeper than that weakens the side wall more than the extra bearing surface helps. Fit matters more than depth: the mating part should slide in with firm hand pressure. Too tight and the case will not assemble; too loose and the joint contributes little.
Cutting a dado on the table saw
The fast method is a stacked dado set: two outer blades with chipper blades between them, adjusted in width with chippers and shims to match the mating part's thickness. Set the width against an actual piece of the mating stock or a reliable measurement of it, because plywood in particular is thinner than its nominal size (a 3/4 inch panel is usually 23/32 inch).
Procedure:
- Mark the dado location and width on the workpiece.
- Install the stack and set blade height for the dado depth (typically 1/4 inch in 3/4 inch stock).
- Run a test cut in scrap of the same thickness and check the fit with the mating part.
- Make the cut in one pass using the miter gauge (never the rip fence for crosscuts) with the workpiece held flat and controlled.
- For a dado wider than the stack's maximum, make the pass, shift the workpiece by a measured amount, and clean up with additional passes.
Without a dado set, repeated passes over a single flat-top-grind blade accomplish the same cut more slowly: mark both walls, make the two outside passes first, then nibble out the middle. A flat-top blade matters here, because an alternating-bevel blade leaves small peaks in the channel floor.
A note for European readers: stacked dado sets are largely a North American method. Most CE-certified table saws cannot physically fit a dado stack because of arbor length, guarding, and blade stopping-time requirements under the Machinery Directive, so the router method below is the standard route in Europe. SawStop's European site explains the specifics; the joint itself is legal, the usual machinery cannot hold the tooling.
Cutting a dado with a router
A router with a straight bit and a fence or edge guide cuts a dado anywhere a table saw cannot reach, including stopped dados and channels in the middle of large panels. Undersized plywood is the common trap: a 23/32 inch panel in a 3/4 inch dado leaves a sloppy gap, so either use an undersized "plywood" bit (23/32 inch is a standard size) or take two passes with a smaller bit sneaking up on the fit.
Procedure:
- Mark both walls of the dado.
- Clamp a straightedge or dado jig across the workpiece, offset for the distance from bit edge to guide.
- Rout in two or more passes of increasing depth rather than one deep pass, which keeps the cut controlled and the floor clean.
- Test the fit on scrap first, then cut the parts.
A T-square style dado jig or a pair of clamped guides is more reliable than a freehand fence for repeated dados, because the offset is captured once and repeated. For a run of identical shelves, one setup gives you every channel in the case.
Common mistakes
- Cutting the dado to nominal plywood thickness instead of the panel's real thickness, leaving a gap that shows.
- Going deeper than half the stock thickness and weakening the side.
- Using the rip fence for a crosscut dado on the table saw, which risks binding and kickback. Use the miter gauge.
- One full-depth router pass, which burns the bit and leaves a rough floor.
- Skipping the test cut, then discovering the fit is wrong on the actual case side.
What success looks like
The shelf slides into the dado with hand pressure, sits without rocking, and stays put when the case is lifted. From the show face the shoulder line is tight and even. Before glue-up, check that the carcass squares up with the shelves installed; that is the dado doing its other job. If the shelf itself will carry books across a span, verify the thickness and span in the shelf sag calculator so the shelf does not deflect even though the joint holds.
Frequently asked questions
Is a dado stronger than screws for shelves?
Yes, for a supported shelf. The shelf's end bears on the channel walls along its whole edge, so the load rests on wood rather than on fastener threads in end grain. Screws or glue hold the parts together; the dado carries the weight.
How deep should a dado be?
About one-third the thickness of the side is the standard target: 1/4 inch deep in 3/4 inch stock. Half thickness is the upper limit; deeper trades away the side's strength for little gain.
Can you cut a dado with a circular saw?
Yes, with a straightedge guide and multiple passes: score both walls, then clear the middle with repeated passes and square the floor with a chisel. It is slower and less clean than a router, but it works for occasional dados in construction lumber.
Why is my dado wider than the shelf is thick?
Plywood is thinner than its nominal size and solid stock varies after milling. Measure the actual shelf stock, not the label, and set the stack or bit passes to that number.
Next steps
- Check a shelf before you cut its dados: shelf sag calculator
- The joint families this belongs to: types of wood joints
- Terminology: dado
- Species for casework: hard maple for crisp shoulders, eastern white pine for utility shelves
- Related joinery: box joint calculator for the case corners